HR202L Humidity sensor
HR202L Humidity sensor is a low cost hygrosensitive module made of moisture sensitive components of organic polymer materials. The resistance of the module changes relative to temperature and humidity.
2 in stock
- Additional Information
- Reviews (0)
- Low Power Consumption
- High Stability
- Excellent Linearity
- Wide Measurement Range
- Quick Response Time
- Low Pollution
- High performance.
- Humidity Range : 20-95%RH
- Temperature Range : 0-60°C
- Input Supply : 1.5V Sine Wave
- Frequency of Operation : 500Hz to 2kHz
- Rated power is 0.2mW sine
- Central value is 31kΩ (at 25Celsius, 1kHz, 1V AC, 60%RH)
- Impedance ranges from 19.8 to 50.2kΩ (at 25Celsius, 1kHz, 1V AC, 60%RH)
- Accuracy : ±5%RH
- Hysteresis : ±1%RH
- Long Term Stability : ±1%RH/year
- Response time is less than 10s
- Polarization should be avoided, input voltage must be 100% alternative.
- Condensation should be avoided
Resistance varies with Temperature & Humidity
|Dimensions||11.3 x 7.3 x 3.5 mm|
Magnetic Reed Switch 22mm0 out of 5
This is a small non-contact magnetic switch which operates under the presence of Magnetic Field. It is commonly referred to as Reed Switch or Magnetic Switch. This switch contains a glass capsule in which two ferrous materials. When exposed to a magnetic field these ferrous materials comes in contact and switch closes due to magnetic attraction. When the magnetic field is removed these materials separates and switch opens.
CMOS VGA Camera Module – OV76700 out of 5
This is a camera image sensor module using IC OV7670, which is a low voltage CMOS image sensor. It provides full functionality of a VGA camera and an image processor. Its output can be full-frame, sub-sampled or windowed 8 bit images in a wide range of formats and can be controlled through Serial Camera Control Bus (SCCB) interface. This interface is compatible with I2C interface which makes it easy to interface with Arduino Boards, Raspberry Pi and microcontrollers.
Force Sensing Resistor Square0 out of 5
This is a force sensor resistor having a square sensing area of 1.5×1.5″. The resistance across the sensor terminals will vary depending upon the amount of pressure applied to the sensing area. As the applied pressure increases, resistance decreases. During no load conditions, the resistance will be greater than 1MΩ. This sensor is able to measure forces in the range of 100g to 10kg. You can easily interface this sensor with Microcontrollers, Arduino Boards, Raspberry Pi etc. using an Analog to Digital Converter (ADC).
Smoke and Flammable Gas Sensor0 out of 5
This sensor module is made using MQ2 Smoke and Flammable Gas Sensor, which uses Tin oxide (SnO2) as the sensor element. Tin oxide has a lower conductivity in clean air. When it comes in contact with flammable gases like LPG, hydrogen, butane, propane, alcohol, smoke and other combustible gases its conductivity increases. This module uses a simple circuit to measure changes in conductivity and output the same. It has dual signal output ie. analogue output and TTL level output. The module also provides a potentiometer to adjust the sensitivity of the sensor.
HC-SR501 PIR Motion Sensor0 out of 5
HC-SR501 PIR Motion Detector is popular for sensing motion using infrared technology with automatic detection. It includes a pyroelectric infrared sensor. It has a detection range below 120° and detection distance adjustable between 3 to 7 meters. It also has a wide operating voltage range of DC4.5V-20V.
Temperature and Humidity Sensor0 out of 5
DHT11 is one of the commonly used sensor module for Temperature and Humidity measurement. It is lab calibrated and provides digital output. DHT11 consist of a NTC temperature measurement component, a resistive type humidity measurement component and a high performance 8-bit microcontroller inside. It outputs data every 2 seconds. It is highly reliable and robust.
Temperature Humidity Sensor – AM23010 out of 5
AM2301 is a digital temperature and humidity sensor module made using a capacitive humidity sensor, a high precision temperature sensor and an 8 bit microcontroller. Former name of this sensor was DHT21. This module provides extremely accurate outputs as it is digitally calibrated using the coefficients stored in the microcontroller. It has a wide operating voltage range, 3.3V ~ 5.2V makes its interface easy with a wide variety of devices. AM2301 sensor module can be easily interfaced with Arduino Boards, Raspberry Pi and other microcontroller units with its single bus interface.
Flex Sensor 2.2″0 out of 5
This is a simple flex sensor of length 2.2 inch manufactured by Spectra Symbol. The resistance across the sensor terminals increases as the sensor is flexed. This is a patented technology by Spectra Symbol. This sensor can be easily interfaced with Microcontrollers, Arduino Boards, Raspberry Pi etc. using an Analog to Digital Converter (ADC).
Soil Moisture Sensor Module0 out of 5
This is a simple water content sensor which can be used to detect soil moisture. It can provide both analog and digital outputs. Analog output can be used to measure the exact moisture content in the soil. While digital output is useful when we want to detect if the soil moisture level crosses a particular level. This level can be easily adjusted using the preset in the panel PCB. This module can be used in Automatic Garden Watering Systems and can be easily interfaced with Arduino Boards, Raspberry Pi, Microcontrollers etc.
Flame Sensor Infrared Receiver0 out of 5
The flame sensor infrared receiver module can detect a flame or light source of wavelength from 760nm to 1100nm. It is particularly useful in fire alarms. The sensitivity of the sensor can be adjusted using the potentiometer provided. The output is given in digital format. The circuit uses a LM393 comparator.