electroSome

Interfacing Rain Sensor with Arduino

Contents

In this article we are going to explain about interfacing Rain Sensor with Arduino. The rain sensor module is an easy tool for rain detection. It operates as a switch when raindrop falls through the raining board and also it measures rainfall intensity. The module features, a rain sensing board and the control board that is separate for more convenience, power indicator LED and an adjustable sensitivity though a potentiometer.

Rain Sensor Module

Raindrop sensor is basically a board on which nickel is coated in the form of lines. It works on the principal of resistance.

Rain Sensor module allows to measure moisture via analog output pins and it provides a digital output when a threshold of moisture exceeds.

The module is based on the LM393 op amp. It includes the electronics module and a printed circuit board that “collects” the rain drops.  As rain drops are collected on the circuit board, they create paths of parallel resistance that are measured via the op amp.

The sensor is a resistive dipole that shows less resistance when wet and more resistance when dry. When there is no rain drop on board it increases the Resistance so we gets high voltage according to V=IR.

When rain drop present it reduces the resistance because water is a conductor of electricity and presence of water connects nickel lines in parallel so reduces resistance and reduces voltage drop across it.

Specifications

Rain Sensor Module

PinOut

Rain Sensor Module – PinOut
Pin Description
Vcc +5 Volts Power Source
GND Ground or negative power source
D0 Digital Output. Goes low when moisture exceeds set threshold.
A0 Analog Output – Zero to five volts. The lower the voltage, the greater the moisture
POWER LED Indicates that power is applied
OUTPUT LED Illuminates when moisture has exceeded threshold set by sensitivity adjustment.
Sensitivity Adjustment Clockwise is more sensitive. Counterclockwise is less sensitive.

Connecting with Arduino

Arduino Rain Sensor – Circuit Diagram

Source Code

Arduino Code

const int sensorMin = 0; 
const int sensorMax = 1024; 
void setup() 
{
  Serial.begin(9600);
}

void loop()
{
  int sensorReading = analogRead(A0);
  int range = map(sensorReading, sensorMin, sensorMax, 0, 3);

  switch (range)
    {
      case 0:
        Serial.println("RAINING");
        break;

      case 1:
        Serial.println("RAIN WARNING");
        break;

      case 2:
        Serial.println("NOT RAINING");
        break;
    }
  delay(1000); 
}

Code Explanation

Initialize the lowest and highest sensor readings with type as an integer and variable name.

const int sensorMin = 0; // sensor minimum
const int sensorMax = 1024; // sensor maximum

The setup() routine runs once when we reset it or power the board. Here we are initializing serial communication at 9600 baud rate.

void setup()
{
  Serial.begin(9600);
}

The loop function runs over and over again forever. Firstly this code reads the analog signal at A0 pin from Rain sensor and maps those measured value with initialized values.

void loop() 
{
  int sensorReading = analogRead(A0);
  int range = map(sensorReading, sensorMin, sensorMax, 0, 3);

Checks the measured value with pre-stored condition and displays the weather condition like RAINING, RAIN WARNING & NOT RAINING.

  switch (range) 
  {
    case 0: // Sensor getting completely wet
      Serial.println("RAINING");
      break;
    case 1: // Sensor getting partially wet
      Serial.println("RAIN WARNING");
      break;

    case 2: // Sensor dry
      Serial.println("NOT RAINING");
      break;
  }
  delay(1000);
}

Working

Make connections according to the above circuit diagram.

Upload the above code into Arduino IDE and test the result on Serial Monitor by soaking the rain sensor into water.

The serial monitor displays the below result based on the amount water drop on the rain sensor module.

Practical Implementation

Arduino Rain Sensor – Practical Implementation

Video

Exit mobile version