electroSome

Interfacing LCD with PIC Microcontroller – CCS C

Ligo George
16x2 Blue Character LCD Module

16x2 Blue Character LCD Module

Contents

In this tutorial we will see How to interface a 16×2 character LCD Module with PIC 16F877A Microcontroller using CCS C Compiler. 16×2 character LCD is a very commonly used LCD module in electronic projects and products. 16×2 means it can display 2 rows of 16 characters. It is a very basic and low cost module. Its other variants such as 16×1, 20×4 are available in the market. In these displays each character is displayed using 5×8 or 5×10 dot matrix. These LCDs commonly uses HD44780 compliant controllers for their operation.

16×2 LCD Pin Diagram

Interface between a microcontroller and LCD can be 4-bit or 8-bit. The difference between 4-bit and 8-bit is how data are send to the LCD. To write an 8-bit character to the LCD module in 8-bit mode, ASCII data is send through the data lines DB0- DB7 and data strobe is given through the E line.

But 4-bit mode uses only 4 data lines. In this mode the 8-bit ASCII data is divided into 2 parts which are send sequentially through data lines DB4 – DB7 with its own data strobe through the E line. The idea of 4-bit communication is to save as much pins that used to interface with LCD. The 4-bit communication is a bit slower when compared to 8-bit. The speed difference is only minimal, as LCDs are slow speed devices the tiny speed difference between these two modes is not significant. Remember that our microcontrollers works in the speed of MHz range. Thus the 4-bit mode data transmission is most commonly used.

CCS C provides a built in library file, “lcd.c” for interfacing LCDs having HD44780 compliant controllers using 4-bit mode communication. Just include this file in your program and enjoy.

CCS C LCD Library

LCD Connections

For the proper functioning of LCD Library, you should define the connections of below 7 pins used for LCD interfacing in the program.

These must be defined before including the header file, it can be done in two ways as given below.

PORT Access Method

This method requires the entire 7 bit interface connected to same GPIO port. It should be defined before including the header file as shown below.

#define LCD_DATA_PORT getenv("SFR:PORTD")

This defines that the entire 7 bit interface is connected to PORTD of PIC Microcontroller.

PIN Access Method

In this method you can connect those 7 bits to any GPIO pins and it should be defined before including the header file as shown below.

//LCD Module Connections
#define LCD_RS_PIN PIN_D1
#define LCD_RW_PIN PIN_D2
#define LCD_ENABLE_PIN PIN_D3
#define LCD_DATA4 PIN_D4
#define LCD_DATA5 PIN_D5
#define LCD_DATA6 PIN_D6
#define LCD_DATA7 PIN_D7
//End LCD Module Connections

Important Functions

lcd_init()

This function must be called before any other lcd functions. It initializes the LCD module with above defined connections.

lcd_putc(c)

This function will display c on the next cursor position of the LCD. You can print strings and characters using this function. You can also use following backslash character constants for sending different commands to LCD.

lcd_gotoxy(x, y)

This function can be used to set cursor position of the LCD, upper left position is (1,1).

lcd_getc(x, y)

This function returns the character at the position (x, y) on the LCD.

lcd_cursor_on(int1 on)

This function can be used to turn the cursor on or off.
Example :

lcd_cursor_on(TRUE); //Turns ON the cursor

lcd_cursor_on(FALSE); //Turns OFF the cursor

Note : For more details you can read the library file “lcd.c” in the location C:/Program Files/PICC/Drivers/.

Usage of printf()

printf() can output a string of characters to standard UART pins or to a specified function. It can be used with CCS C LCD library to format output strings. By thus we can print integers, floating point numbers etc using this.

Syntax :

printf(fname, cstring, values...);

Where,

Format

The generic form of format is %nt. where n is optional which may be 1 – 9 to specify number of characters to be outputted or 01 – 09 to indicate leading zeros or 1.1 to 9.9 for floating point and %w formats. t is the type which may be one of the following.

t Type
c Character
s Sting or Character
u Unsigned Integer
d Signed Integer
Lu Long Unsigned Integer
Ld Long Signed Integer
x Hex Integer – lower case
X Hex Integer – upper case
Lx Hex Long Integer – lower case
LX Hex Long Integer – upper case
f Float with truncated decimal
g Float with rounded decimal
e Float in exponential format
w Unsigned Integer with decimal place inserted. Specify two numbers for n. The first is a total field width. The second is the desired number of decimal places.

Example :

To print an integer :

printf(lcd_putc,"Count = %d", i);

When i = 0, output will be : Count = 0

Circuit Diagram

Interfacing LCD with PIC Microcontroller – Circuit Diagram

CSS C Code

//LCD Module Connections
#define LCD_RS_PIN PIN_D1
#define LCD_RW_PIN PIN_D2
#define LCD_ENABLE_PIN PIN_D3
#define LCD_DATA4 PIN_D4
#define LCD_DATA5 PIN_D5
#define LCD_DATA6 PIN_D6
#define LCD_DATA7 PIN_D7
//End LCD Module Connections

#include <main.h>
#include <lcd.c>

#use delay (clock=8000000)

void main()
{
  int i=0;

  lcd_init();
  Delay_ms(100);

  while(TRUE)
  {
    lcd_putc('\\f');                   //Clear Display
    lcd_putc("Hello World");
    Delay_ms(2000);
    lcd_putc('\\f');                   //Clear Display
    lcd_putc("Welcome To");
    lcd_gotoxy(1,2);
    lcd_putc("LCD Library");
    Delay_ms(2000);
    lcd_putc('\\f');                   //Clear Display
    printf(lcd_putc,"Count = %d", i); //Display Count
    Delay_ms(2000);
    i++;
  }
}

Downlaod

You can download CCS C files and Proteus files here.

 

Exit mobile version