Generating PWM with PIC Microcontroller using CCP Module

19Jan

Generating PWM with PIC Microcontroller using CCP Module

By MikroC, PIC Microcontroller, Tutorials , , , , 114 Comments

Contents

PWM is a technique used to generate analog output signal using digital signals. It is commonly used to control average power delivered to a load, motor speed control, generating analog voltage levels and for generating analog waveforms.

CCP Modules are available with a number of PIC Microcontrollers. CCP stands for Capture/Compare/PWM. Using PWM module is far more easier and cost effective than using extra chips for PWM generation.  MikroC Pro for PIC Microcontroller provide built-in library for PWM which makes our task very simple.

MikroC Functions

  • PWM1_Init(constant long frequency) : This function initializes the PWM module with duty ratio 0. Frequency parameter is the desired frequency in Hz. It should be a numeric constant, should not be a variable.
  • PWM1_Set_Duty(unsigned short duty_ratio) : This function is used to set the duty cycle of the PWM. The parameter duty_ratio takes values from 0 to 255, ie 0 means 0% , 127 means 50% and 255 means 100% duty cycle. The PWM1_Init() routine must be called before using this.
  • PWM1_Start() : This function starts the PWM output. PWM1_Init() must be called before calling this routine,
  • PWM1_Stop() : This function stops the PWM output. PWM1_Init() must be called before calling this routine. PWM1_Start() should be called before calling this function otherwise calling this function will not have any effect as PWM module is not running.

Note 1 :  For microcontrollers with more than one CCP module, to use the desired CCP module for PWM generation simply change the number “1”  in the prototype with desired module number. eg: PWM2_Init(5000), PWM2_Start().

Note 2 : All PWM modules in a PIC Microcontroller uses Timer 2 for its operation, so you cannot set different frequencies for different PWM modules.


In this tutorial we are using PIC 16F877A for demonstrating PWM generation using CCP module. PIC 16F877A contains two CCP modules.

Circuit Diagram – Using internal PWM Module of PIC

In the below circuit four switches are provided for controlling the Duty Ratio of PWM generated by two CCP modules of the PIC Microcontroller.

  • Switch 1 : To increase the Duty Ratio of PWM produced by CCP1
  • Switch 2 : To decrease the Duty Ratio of PWM produced by CCP1
  • Switch 3 : To increase the Duty Ratio of PWM produced by CCP2
  • Switch 4 : To decrease the Duty Ratio of PWM produced by CCP2
Using Internal PWM Module PIC Microcontroller Circuit Diagram
Using Internal PWM Module PIC Microcontroller Circuit Diagram

The output of the two CCP modules are given to a CRO to observe the changes in pulse width. It may be given to two LEDs and you can see the changes in brightness as Duty Ratio changes.

MikroC Program

void main()
{
  short current_duty_1  = 16; // initial value for current_duty_1
  short current_duty_2 = 16;  // initial value for current_duty_2

  TRISD = 0xFF; // PORTD as input
  TRISC = 0x00; // PORTC as output

  PWM1_Init(5000);  // Initialize PWM1
  PWM2_Init(5000);  // Initialize PWM2

  PWM1_Start();  // start PWM1
  PWM2_Start();  // start PWM2

  PWM1_Set_Duty(current_duty_1); // Set current duty for PWM1
  PWM2_Set_Duty(current_duty_2); // Set current duty for PWM2

  while (1)        // endless loop
  {
     if (!RD0_bit)   // if button on RD0 pressed
     {
      Delay_ms(40);
      current_duty_1++;  // increment current_duty_1
      PWM1_Set_Duty(current_duty_1);  //Change the duty cycle
     }

    if (!RD1_bit)               // button on RD1 pressed
    {
      Delay_ms(40);
      current_duty_1--;  // decrement current_duty_1
      PWM1_Set_Duty(current_duty_1);
     }

    if (!RD2_bit)     // if button on RD2 pressed
    {
      Delay_ms(40);
      current_duty_2++;    // increment current_duty_2
      PWM2_Set_Duty(current_duty_2);
     }

    if (!RD3_bit)       // if button on RD3 pressed
    {
      Delay_ms(40);
      current_duty_2--;   // decrement current_duty_2
      PWM2_Set_Duty(current_duty_2);
     }

    Delay_ms(10);      // slow down change pace a little
  }
}

I thinks the program is self explanatory, so if you have any doubts please comment below…

Download

You can download the MikroC Source Code, Proteus files etc here…

Video

Share this post

Author

Follow Me on LinkedIn

  • HI,
    I have programmed the pic16f88 the below program. Pin RA0 & RA1 are connected to 2 push buttons for increment or decrement the Pwm & Pin RB0 is used for ccp1 out & connected to Led . After powering the circuit i can see the pwm on RB0 Led and on scope also but no change happens after pushing 2 push buttons … Can you please help ? Internal Oscillator frequency is set to 8 Mhz.

    void main()
    {
    short current_duty_1 = 16; // initial value for current_duty_1

    TRISA = 0xFF; // PORTA as input
    TRISB = 0x00; // PORTB as output

    PWM1_Init(5000); // Initialize PWM1
    PWM1_Start(); // start PWM1

    PWM1_Set_Duty(current_duty_1); // Set current duty for PWM1

    while (1) // endless loop
    {
    if (!RA0_bit) // if button on RD0 pressed
    {
    Delay_ms(40);
    current_duty_1++; // increment current_duty_1
    PWM1_Set_Duty(current_duty_1); //Change the duty cycle
    }

    if (!RA1_bit) // button on RD1 pressed
    {
    Delay_ms(40);
    current_duty_1–; // decrement current_duty_1
    PWM1_Set_Duty(current_duty_1);
    }

    Delay_ms(10); // slow down change pace a little
    }
    }

  • Sir our thesis is all about buck-boost converter using pic16f877a..can you help me how to use the pins on that microcontroller so that the switch of our microcontroller is that pic

  • Please help me…i want to control light brightness by using PIC Micro
    controller with button (PWM)..I found this in your site. Why my LED
    always blinking…in oscillation PWM working. Please give me a proper
    solution or give me a source code for light brightness control PIC with
    push buttons

  • how to generate 3 different delayed pulses to switch on 3 mosfets in micro c?

    .

  • Do anybody have a code for PLECS [C-subscript] for PWM generation of three phase induction motor?

  • void main() {
    TRISC.F2=0;
    TRISC.F1=0;
    T2CON.T2CKPS1=0;
    T2CON.T2CKPS0=1;
    PR2=0XF9;
    CCP1CON.CCP1M3=1;
    CCP1CON.CCP1M2=1;
    CCP1CON.CCP1M1=0;
    CCP1CON.CCP1M0=0;
    CCPR1L=0X52;
    CCP1CON.CCP1X=0;
    CCP1CON.CCP1Y=0;
    T2CON.TMR2ON=1;
    DELAY_us(250);
    T2CON.T2CKPS1=0;
    T2CON.T2CKPS0=1;
    PR2=0XF9;
    CCP2CON.CCP2M3=1;
    CCP2CON.CCP2M2=1;
    CCP2CON.CCP2M1=0;
    CCP2CON.CCP2M0=0;
    CCPR2L=0X52;
    CCP2CON.CCP2X=0;
    CCP2CON.CCP2Y=0;
    T2CON.TMR2ON=1;

    while(1);
    }
    this is the code and i am getting two PWM without delay

  • sir how can i produce two pwm signals with same duty cycle and a delay between two using mikroC I tried and i am not able to give delay

  • Hi dear George,first of all thank you,sir i need to 3 phase pwm for 3 phase inverter progect with 120 and 240 degree phase shift?can you help me?
    regards

  • sir, i have to generate a pulse of 2 second period and 50 % duty cycle in pic16f877a having clock frequency is 8 mhz. please help…

  • Hey, I am making SPIM using micro controller, So can I provide pulses to my inverter with this (16F877A) micro controller?

  • hello sir thank you for you share this with us.. for inverter i am using spwm technique for 1Khz carrier frequency. and pic16f886 chip. can you plz help me in cooding for this converter.?

  • hello sir thank you for you share this with us.. for inverter i am using spwm technique for 1Khz carrier frequency. and picf16f**& chip. can you plz help me in cooding for this converter.?

  • I am new to PIC and I would like to use it to make 2 PWM signals that are shifted. Is there a standard command/way to do this?

  • sir ligo, how can i control the speed of two dc water pump… one for inlet and one for outlet.. im using pic16f877a with ultrasonic as a sensor… i need it asap for my final year project…
    i appreciate it if u help me 🙂

  • hi sir am new to mikro c compiler,in eariler am using mplab and ccs compilier. i need to pwm program for pic18f66k80 how can i use the same code for that ic please tell me . thanks in advance

  • #include

    #use delay (clock = 20000000)

    #fuses hs,nowdt,nobrownout,noprotect

    #byte PORTB=0xF81 //port B will be used as output

    #byte PORTC=0xF82 //port C also will be used as output

    #byte PORTD=0xF83//port D as input 12V

    void main()

    {

    set_tris_d(1);//set portD as input connected to pin 12V

    set_tris_b(0); //set portB as output. portB set as ccp1 connected to green light.

    set_tris_c(0);//set portD as output. c1 and c3 connected to red and blue.

    setup_ccp1(ccp_pwm); // set ccp1 as pwm

    setup_timer_2(T2_DIV_BY_16,225,1); //set timer2 divisian 255,internal as 1

    while(1)

    {

    if(input(pin_d0))

    {

    output_high(pin_b3); //to ON enable

    output_high(pin_c1); //to make led move forward

    output_low(pin_c2); //when input b0 is high

    set_pwm1_duty(150);//at 7.03v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(175);//at 8.20v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(200);//at 9.44v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(225);//at 10.55v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(250);//at 11.72v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(255);//at 11.96v

    set_timer2(0);

    delay_ms(40);

    }

    else

    {

    output_high(pin_b3);//to on enable

    output_low(pin_c1);//to make led move backward

    output_high(pin_c2);//when input b0 is low

    set_pwm1_duty(150); //at 7.03v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(175);//at 8.20v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(200);//at 9.44v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(225);//at 10.55v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(250);//at 11.72v

    set_timer2(0);

    delay_ms(40);

    set_pwm1_duty(255);//at 11.96v

    set_timer2(0);

    delay_ms(40);

    }

    }

    }

    i dunno what happen, but when i attached to my 9v battery, they only give red color..

  • Sir, can you tell us how can we control a motor (both DC and AC) using PID controlling according to an analog input. please put a tutorial on that. i think that is one of major issue among most students. (MIkRO C and arduino)

  • thank you it worked. can you tell us how can we control a motor using PID controlling according to an analog input. please put a tutorial on that. i think that is one of major issue among most students.

  • Hi, I am using pic16f887 to generate 3 pwm signals for my 3 phase ac motor. I have done the first 2 pwm signals because there are in built modules for pwm in the pic but the third one i need to make with interrupts and timers. Could you please help? And due to it being a 3 phase motor, the three pwm signals have to spaced by 120degrees, any ideas how to do that aswell please. thanks

  • Dear Mr. Ligo
    Can you help me providing a simple code of PWM for PIC 12F675 with which I can build a simple obstacle sensor.
    I am a senior citizen and passing my time with experimenting with different circuit (discreat ICs) & interested in PIC, already experimented with simple PIC codes published in net…. I have read your tutorials and liked them as those are very clearly explained. My requirement is like this
    1) One pin of PIC 12F675( with this I am comfortable) will deliver 40kHz signal to an ultrasonic Tx module at a regular intervels.
    2) Another pin of PIC as input where another Ultrasonic RX is connected will receive the reflected signal.
    3) 3rd. pin will produce PWM signal whose duty cycle will change in proportion with the received signal strength.
    That mean if I connect a LED here, its brightness will be maximum when the obstacle is very close to the sensors
    Try to help me, Please send the code to my mail. I have Micro C.
    Thanks.

    D. Ghosh.
    [email protected].

  • hey Ligo, can you tell me the rating of the motors for which this cct is applicable? and is it verified in terms of hardware ???

  • hello , I wanna help with the title “Closed-loop DC Motor Drive for
    maintaining Constant speed & Torque on Variable loads”. I want to use PIC controller with PWM for this purpose and in addition , PID controller would be used to handle the feedback signal and give it to the Motor drive circuitry.

  • thanks bro
    please i have been written that code of buck converter but my mosfet can not be work
    please can you help my how to inter that code

  • Sir can you please provide me the code to generate a single pulse with a specific frequency to drive a stepper motor one step?

  • read adc value…… it will be a 10bit number.
    ..
    eg :
    unsigned int a;
    a = ADC_Read(0);
    then divide it by 4,
    eg :
    char b;
    b = a/4;
    Then write pwm
    PWM1_Set_Duty(b);

  • i want to control a LED using PWM according to a variable resister(protentio meter). can you plese explain me the micro c code for it? ADC to PWM . using micro controller

  • Hello Ligo George.. Thank you very much! I built one of this and it worked perfectly for my application (Fan PWM controller).. Now I’m planning to use this for some other application, but first, will this work on 120Khz output? I’m also thinking about hooking it up to an LCD to show the current duty cycle, or maybe the fan rpm someday if I can learn how to program it.. Thanks a lot!

  • Ok I got it now.. I’ll try to program this on the PIC tommorow, and I hope it works.. Thanks!

  • Thank you very much for all of these, it really shed some light on how can I use PIC18F for such an application. This design is actually what I really need except for 1 thing, I need the PWM output to be at 25Khz. As you have attached the hex and source files here, I tried to modify it myself from 5000 to 25000. But I’m having problem compiling it to hex. I tried cx8 and Hi-tech PICC compiler to no avail. The cx8 shows “Error [1098]” while the PICC tool suite shows “Halting build on first failure as requested.” error. Can you help me in modifying the code to 25khz and compiling it? I’m really sorry for I’m just a newbie in PIC programming. Also, will the circuit be able to function properly with 25khz output? Thanks! =)

  • Hi,

    I’m looking for a solution for every time a rising edge occurs on RB1 I should increase the duty cycle by 10 on the signal provided by RB0.Every time a rising edge occurs on RB2 I should decrease the duty cycle by 10% on the signal provided by RB0.

    I achieved to generate a PWM signal on RBO with a period of 200us and a 10% duty cycle but I don’t know how increase or decrease the duty cycle, using only a main.c solution.

    Thanks

  • Ligo,

    I would want to find out if i can use PIC16F877A and the code above to control 2-phase interleaved dc-dc converter? I am using four MOSFETs of which i will have PWM on two going from high to low and the other two will have PWM going from low to high. Constant duty cycle of 0.5, frequency is 50kHz. Please advise.

  • Refer the datasheet of your microcontroller…. If the pwm module of your microcontroller is similar to 16F877A’s PWM module, you can use above code.. otherwise you need to modify my functions…. most probably you need to modify my codes. .as you microcontroller is 18F ..

  • Use Soft generated PWM… using interrupt… timer 2 overflow interrupt will be generated while using pwm… so use interrupt service routine to generate soft pwm with a delay
    if the output pin is PORTB 0
    void interrupt ISR()
    {
    __delay_ms(your delay here);
    if(RB0 == 1)
    RB0 = 0;
    else
    RB0 = 1;
    }

  • Mr.Ligo, Good work. I’m trying to generate code for the following.
    I wanna generate two independent pulses- So we will PWM1 and PWM2 with same frequency.
    The pulses are of same duty cylcle.. But, There should be a delay between two pulses.
    For example- Let us say the Freq is 1000. therefore the Time = 1ms In this case, Pulse 1 starts at 0 sec, second pulse should start after 0.5ms. What is the solution. I have tried so many things using PWM1 aND pwm2 WITH DELAY. bUT, NOTHING WORKS>>>

  • thank you sir,,means that we do not need to combine dc code,,just put pwm coding….
    one more thing,,i tried to combine micro c coding for stepper,dc and servo motor but i got some errors..can you give me some tips on how to combine micro c coding,,,actually im doing training kit using pic 16f877a…a part of that contains dc,, stepper and servo motor….i got some problem on how to combine those 3 coding…
    hope can help,,really appreciate…

  • plz suggest me a microcontroller having more than four independent PWM.currently I am using dsPIC33f family that has 4 PWM

  • can we control heater with this pwm, and the tempreture of heater can control with tempreture controller and the digital output of tempreture controller replace with digital INCREASE or DECREASE inputs

  • You may use a ir sensor and ir led for that… by counting the cutting rate of ir falling on ir sensor.. you can find the speed of the motor..

  • Using PWM we can produce any analog voltage…. as duty cycle varies the average voltage of it also vary… for a 5V pwm..
    duty cycle
    100% gives 5V
    50% gives 2.5V
    0% gives 0V..

    thus switch the H bridge according to sine wave..

  • sir we are using electronic speed controller rated 40amps. to control the speed of the brushless motor likewise the brushless motor nee. The electronic speed controller is like a servo motor with input signal whose pulse width varies from 1 ms to 2 ms. We want to have a program that can generate these pulses to turn on and control the brushless motor. Do you have a program for that sir?

  • I am a bit of newbie, maybe what I should have asked for is how to generate the sine wave form from the same PIC and use PWM to make an H-bridge Inverter

  • thank you sir. another question sir what is the output of the pic using ccp1 module to the input of the electronic speed controller? and how can i control like a servo controller? thank you sir

  • Thanks so much for the tutorial. How do I adapt this code and circuit for H-Bridge Sine wave Inverter

  • You can control the speed of a motor using its ccp1 module… there is only a littile change in the source code since we are using mikro c… you can simply change it according to the pins you are using..

  • Sir how to control the motor using the electronic speed controller and pic using pic16f628a? what is probable source code of mikroC for that?

  • Sir i cant understand the command ‘if (!RD0_bit)’… can we use ‘if(RD0==1)’ instead of ‘if (!RD0_bit)’???

    • Related Posts

    SCILAB Logo

    Getting Started with Scilab – Beginners Tutorial

    July 13, 2013 | | SCILAB, Tutorials | , | 0 Comments

    SCILAB provides a powerful computation environment along with a rich collection of numerical algorithms for both the engineering and scientific... Read More

    HC-SR04 Ultrasonic Sensor

    Interfacing HC-SR04 Ultrasonic Sensor with PIC Microcontroller

    August 12, 2014 | | Embedded, MikroC, MPLAB XC8, PIC Microcontroller, PIC Microcontroller, Projects | , , , , , , , , , | 226 Comments

    HC-SR04 Ultrasonic Distance Sensor is a popular and low cost solution for non-contact distance measurement function. It is able... Read More

    Push Button Switch

    Using Switch with Raspberry Pi – Python

    January 26, 2015 | | Electronics, Python Rpi, Raspberry Pi, Tutorials | , , | 0 Comments

    I hope that you already go through our tutorial, LED Blinking using Raspberry... Read More

    Comparator Symbol

    Using Analog Comparator in PIC Microcontroller

    June 25, 2012 | | MikroC, PIC Microcontroller, Tutorials | , , , , | 12 Comments

    Comparator Module in PIC

    Analog Comparator is a device which compares two voltage signals and switches its output to indicate which one is... Read More

    Led Blinking using Raspberry Pi – Python

    September 25, 2014 | | Python Rpi, Raspberry Pi, Tutorials | , , | 4 Comments

    Led blinking is one of the beginner circuits which helps one to get acquainted with GPIO pins of Raspberry Pi.... Read More

    Pulse Width Modulation

    Generating PWM with PIC Microcontroller using Hi-Tech C

    October 23, 2013 | | Hi-Tech C, PIC Microcontroller, Tutorials | , , , , , | 35 Comments

    PWM (Pulse Width Modulation) is a powerful technique used to generate analog voltage using digital signals. It has a wide... Read More

    Microchip Pic Microcontroller

    Read Modify Write Problem with Mid-Range PIC Microcontrollers

    June 16, 2014 | | Electronics, PIC Microcontroller, Tutorials | , , , , , , , | 2 Comments

    RMW Problem with PIC 16F Family

    Microchip's mid-range PIC Microcontrollers use a sequence of operations : Read, Modify and Write to... Read More

    16x2 Character LCD

    Interfacing LCD with 8051 using Keil C – AT89C51

    May 10, 2013 | | 8051 Microcontroller, Tutorials | , , , , , | 131 Comments

    Liquid Crystal Display (LCD) is very commonly used electronic display module and having a wide range of applications such as... Read More

    Flash Magic Tool

    Flashing LPC2148 – ARM Microcontroller Tutorial – Part 2

    January 15, 2020 | | ARM, ARM7, Tutorials | , , , , | 0 Comments

    In this tutorial we will learn how to flash an LPC2148 microcontroller using on-chip serial (UART) ISP bootloader with Flash... Read More

    Servo Motor

    Interfacing Servo Motor with Arduino Uno

    May 5, 2020 | | Arduino, Tutorials | , , | 0 Comments

    In this tutorial we will learn how to interface servo motor with Arduino Uno. Servo Motor is an electrical linear... Read More

    >